Comparing risk assessment methods for work-related musculoskeletal disorders with in vivo joint loads during manual materials handling.

The validity of observational methods in ergonomics is still challenging research. Criterion validity in terms of concurrent validity is the most commonly studied. However, studies comparing observational methods with biomechanical values are rare. Thus, the aim of this study is to compare the Ovako Working Posture Analysing System (OWAS) and the Rapid Entire Body Assessment (REBA) with in vivo load measurements at hip, spine, and knee during stoop and squat lifting of 14 participants. The results reveal that OWAS and REBA action levels (AL) can distinguish between different in vivo load measurements during manual lifting. However, the results also reveal that the same OWAS- and REBA-AL do not necessarily provide equal mean values of in vivo load measurements. For example, resultant contact force in the vertebral body replacement for squat lifting ranged from 57% body weight (%BW) in OWAS-AL1 to 138%BW in OWAS-AL3 compared to 46%BW in REBA-AL0 and 173%BW in REBA-AL3. Furthermore, the results suggest that the performed squat lifting techniques had a higher risk for work-related musculoskeletal disorders than the performed stoop lifting techniques.

In vivo load on knee, hip and spine during manual materials handling with two lifting techniques.

It is generally accepted that the lifting technique strongly influences physical loads within the human body and, thus, the risk of musculoskeletal disorders. However, there is a lack of knowledge regarding whether particular lifting techniques are effective in reducing loads. Hence, this retrospective study quantified (partly published) in vivo loads at joints within the human body during two typical lifting techniques, stoop lifting and squat lifting. Patients who had received instrumented implants underwent in vivo load measurements at either the knee (two patients), the hip (eight patients), or the upper lumbar spine (four patients) while lifting a 10 kg weight frontally with either straight (stoop) or bent (squat) knees. Contact forces and moments and the orientation of the contact force vector were determined and examined using the paired t test of Statistical Parametric Mapping. The two lifting techniques did not differ in terms of load magnitudes but did differ in terms of directions: (i) at the hip joint, the load vector varied significantly (p < 0.05) in the frontal and sagittal planes, (ii) at the knee joint, the load vector differed significantly (p < 0.05) in the sagittal plane (iii) while the load vector and magnitude did not differ at the upper lumbar spine (p > 0.05). Our findings indicate that the lifting technique causes changes in the orientation rather than the magnitude of lower extremity joint contact loads. Even though this quantification could only be performed in a small group of patients, the quantification of the relevance of such lifting technique recommendations will hopefully guide future recommendations towards a more scientific interpretation.

Loading of the Hip and Knee During Swimming: An in Vivo Load Study.

BACKGROUND: Swimming is commonly recommended as postoperative rehabilitation following total hip arthroplasty (THA) and total knee arthroplasty (TKA). So far, in vivo hip and knee joint loads during swimming remain undescribed. METHODS: In vivo hip and knee joint loads were measured in 6 patients who underwent THA and 5 patients who underwent TKA with instrumented joint implants. Joint loads, including the resultant joint contact force (F Res ), torsional moment around the femoral shaft axis or the tibial axis (M Tors ), bending moment at the middle of the femoral neck (M Bend ), torsional moment around the femoral neck axis (M Tne ), and medial force ratio (MFR) in the knee, were measured during breaststroke swimming at 0.5, 0.6, and 0.7 m/s and the breaststroke and crawl kicks at 0.5 and 1.0 m/s. RESULTS: The ranges of the median maximal F Res were 157% to 193% of body weight for the hip and 93% to 145% of body weight for the knee during breaststroke swimming. Greater maxima of F Res (hip and knee), M Tors (hip and knee), M Bend (hip), and M Tne (hip) were observed with higher breaststroke swimming velocities, but significance was only identified between 0.5 and 0.6 m/s in F Res (p = 0.028), M Tors (p = 0.028), and M Bend (p = 0.028) and between 0.5 and 0.7 m/s in F Res (p = 0.045) in hips. No difference was found in maximal MFR between different breaststroke swimming velocities. The maximal F Res was significantly positively correlated with the breaststroke swimming velocity (hip: r = 0.541; p < 0.05; and knee: r = 0.414; p < 0.001). The maximal F Res (hip and knee) and moments (hip) were higher in the crawl kick than in the breaststroke kick, and a significant difference was recognized in F Res Max for the hip: median, 179% versus 118% of body weight (p = 0.028) for 0.5 m/s and 166% versus 133% of body weight (p = 0.028) for 1.0 m/s. CONCLUSIONS: Swimming is a safe and low-impact activity, particularly recommended for patients who undergo THA or TKA. Hip and knee joint loads are greater with higher swimming velocities and can be influenced by swimming styles. Nevertheless, concrete suggestions to patients who undergo arthroplasty on swimming should involve individual considerations. LEVEL OF EVIDENCE: Therapeutic Level IV . See Instructions for Authors for a complete description of levels of evidence.

Periarticular muscle status affects in vivo tibio-femoral joint loads after total knee arthroplasty.

Background: Total knee arthroplasty (TKA) is a highly effective treatment for severe knee osteoarthritis that is increasingly performed in younger, more active patients. As postoperative muscular impairments may negatively affect surgical outcomes and implant longevity, functional muscle recovery gains increasing importance in meeting future patient demands. This study aimed to assess the status of periarticular muscles in the long-term follow-up after TKA and to evaluate its impact on in vivo tibio-femoral joint loads. Methods: A case series was created, with eight patients with knee osteoarthritis. All subjects received an instrumented knee implant in unilateral TKA. Native computed tomography scans, acquired pre and postoperatively, were used to evaluate distal muscle volumes and fatty infiltration. In vivo tibio-femoral joint loads were measured telemetrically during standing, walking, stair climbing and chair rising and were correlated to muscle status. Results: Postoperatively a reduction in fatty infiltration across all periarticular muscles was pronounced. High average peak loads acted in the tibio-femoral joint ranging from 264% during stand-to-sit activities up to 341% body weight (BW) during stair descent. Fatty infiltration of the m. quadriceps femoris and hamstrings were associated with increased tibio-femoral joint contact forces during walking (r = 0.542; 0.412 and 0.766). Conclusion: The findings suggest that a fatty infiltration of periarticular muscles may lead to increased tibio-femoral joint contact forces. However, we only observed weak correlations between these parameters. Improvements in functional mobility and the restoration of a pain-free joint likely explain the observed postoperative reductions in fatty infiltration. Perioperative rehabilitation approaches targeting residual impairments in muscle quality could, contribute to reduced tibio-femoral joint loads and improved long-term outcomes of TKA. However, it has to be pointed out that the study included a small number of patients, which may limit its validity.

Is Training With Gym Machines Safe After Hip Arthroplasty?-An In Vivo Load Investigation.

Background: Training with gym machines is one of the most popular physical activities after total hip arthroplasty (THA). However, to date, there are no evidence-based recommendations for physical activity after THA, worldwide. The aim of the study is to evaluate the in vivo hip joint loads during exercises on four widely used gym machines in order to provide a source for an evidence-based patient counselling for arthroplasty surgeons. Methods: The in vivo hip joint loads in seven patients (59.6 ± 6.4 years, 28.6 ± 2.1 kg/m2) with instrumented hip implants were assessed. The resulting force (Fres), bending moment (Mbend), and torsional moment (Mtors) were evaluated during the training on leg curl/leg extension machines (loads: 20, 30, and 40 kg), leg press machine [backrest: 10°, 30°, and 60°; load: 50, 75, and 100%BW (bodyweight)], and a rope pull machine (abduction/adduction/flexion/extension; each ipsi- and contralateral; load 10 kg). These loads were compared with the loads during walking on treadmill at 4 km/h (median peak values: Fres 303%BW, Mbend 4.25%BWm, and Mtors 2.70%BWm). Results: In each of the four performed exercises with a total of 23 different load conditions or exercise modes analyzed, a significantly lower or not different load was detected with respect to Fres, Mbend, and Mtors measured while walking with 4 km/h. Nevertheless, Fres and Mbend demonstrated a trend to increased loading during the ipsilateral monopod standing rope pull exercises hip flexion, extension, and abduction. Conclusion: Based on our investigation, we assume that the investigated gym machines and external loads can be considered mainly as low-impact sports (with some exceptions) and thus as safe physical activity after THA. Due to the fact that the examinations were conducted in the mean 17.4 months after THA, the applicability of the results to the immediate postoperative period is limited.

Ground reaction forces and external hip joint moments predict in vivo hip contact forces during gait.

Younger patients increasingly receive total hip arthroplasty (THA) as therapy for end-stage osteoarthritis. To maintain the long-term success of THA in such patients, avoiding extremely high hip loads, i.e., in vivo hip contact force (HCF), is considered essential. However, in vivo HCFs are difficult to determine and their direct measurement is limited to instrumented joint implants. It remains unclear whether external measurements of ground reaction forces (GRFs), a non-invasive, markerless and clinic-friendly measure can estimate in vivo HCFs. Using data from eight patients with instrumented hip implants, this study determined whether GRF time series data, alone or combined with other scalar variables such as hip joint moments (HJMs) and lean muscle volume (LMV), could predict the resultant HCF (rHCF) impulse using a functional linear modeling approach. Overall, single GRF time series data did not predict in vivo rHCF impulses. However, when GRF time series data were combined with LMV of the gluteus medius or sagittal HJM using a functional linear modeling approach, the in vivo rHCF impulse could be predicted from external measures only. Accordingly, this approach can predict in vivo rHCF impulses, and thus provide patients with useful insight regarding their gait behavior to avoid hip joint overloading.

Overstretching Expectations May Endanger the Success of the "Millennium Surgery".

Total hip arthroplasty (THA) is an extremely successful treatment strategy. Patient expectations, however, have increased; if not properly guided by surgeons, at present, patients expect next to pain-free restoration of the joint and a fast return to work and sports. While the revision rates after THA also increased in younger patients, knowledge on musculoskeletal loads still remains sparse, and the current recommendations on postoperative rehabilitation are based on expert opinions only. The aim of this study was to unravel biomechanical contact conditions in "working age" (<60 years, 53.5 ± 3.0 years) and "retirement age" (>60 years, 67.7 ± 8.6 years) patients during activities recommended post-THA. We hypothesized that working age patients would show substantially increased hip contact loads compared to older patients. The in vivo joint contact force (F res) and torsion torque (M tors), reflecting the main contact load situation, experienced during activities of daily living and sports activities were measured in a unique group of 16 patients with instrumented THA. We summarized patient activities and sports recommendations after THA mentioned within the literature using PubMed (without claim of completeness). The measurements showed that younger working age patients experienced significant (p = 0.050) increased M tors (21.52 ± 9.11 Nm) than older retirement age patients (13.99 ± 7.89 Nm) by walking. Bowling, as a recommended low-impact sport, was associated with F res of up to 5436 N and M tors of up to 108 Nm in the working age group, which were higher than the F res (5276 N) and M tors (71 Nm) during high-impact soccer. Based on our results, age was proven to be a discriminator in joint loading, with working age patients presenting with increased loads compared to retirement age patients, already during daily activities. The current patient recommendations have led to further increased joint loadings. If THA cannot be delayed in a patient, we propose counselling patients on a carefully considered return to sports, focusing on low-impact activities, as indicated hereby. The findings from this work illustrate the need to provide critical feedback to patient expectations when returning to work and sports activities. Patients returning to more intensive sports activities should be carefully monitored and advised to avoid as much overloading as possible.

Surgical cup placement affects the heating up of total joint hip replacements.

The long-term success of highly effective total hip arthroplasty (THA) is mainly restricted by aseptic loosening, which is widely associated with friction between the head and cup liner. However, knowledge of the in vivo joint friction and resulting temperature increase is limited. Employing a novel combination of in vivo and in silico technologies, we analyzed the hypothesis that the intraoperatively defined implant orientation defines the individual joint roofing, friction and its associated temperature increase. A total of 38,000 in vivo activity trials from a special group of 10 subjects with instrumented THA implants with an identical material combination were analyzed and showed a significant link between implant orientation, joint kinematics, joint roofing and friction-induced temperature increase but surprisingly not with acting joint contact force magnitude. This combined in vivo and in silico analysis revealed that cup placement in relation to the stem is key to the in vivo joint friction and heating-up of THA. Thus, intraoperative placement, and not only articulating materials, should be the focus of further improvements, especially for young and more active patients.

Quantifying Asymmetry in Gait: The Weighted Universal Symmetry Index to Evaluate 3D Ground Reaction Forces.

Though gait asymmetry is used as a metric of functional recovery in clinical rehabilitation, there is no consensus on an ideal method for its evaluation. Various methods have been proposed to analyze single bilateral signals but are limited in scope, as they can often use only positive signals or discrete values extracted from time-scale data as input. By defining five symmetry axioms, a framework for benchmarking existing methods was established and a new method was described here for the first time: the weighted universal symmetry index (wUSI), which overcomes limitations of other methods. Both existing methods and the wUSI were mathematically compared to each other and in respect to their ability to fulfill the proposed symmetry axioms. Eligible methods that fulfilled these axioms were then applied using both discrete and continuous approaches to ground reaction force (GRF) data collected from healthy gait, both with and without artificially induced asymmetry using a single instrumented elbow crutch. The wUSI with a continuous approach was the only symmetry method capable of identifying GRF asymmetry differences in different walking conditions in all three planes of motion. When used with a continuous approach, the wUSI method was able to detect asymmetries while avoiding artificial inflation, a common problem reported in other methods. In conclusion, the wUSI is proposed as a universal method to quantify three-dimensional GRF asymmetries, which may also be expanded to other biomechanical signals.

Loading of the hip and knee joints during whole body vibration training.

During whole body vibrations, the total contact force in knee and hip joints consists of a static component plus the vibration-induced dynamic component. In two different cohorts, these forces were measured with instrumented joint implants at different vibration frequencies and amplitudes. For three standing positions on two platforms, the dynamic forces were compared to the static forces, and the total forces were related to the peak forces during walking. A biomechanical model served for estimating muscle force increases from contact force increases. The median static forces were 122% to 168% (knee), resp. 93% to 141% (hip), of the body weight. The same accelerations produced higher dynamic forces for alternating than for parallel foot movements. The dynamic forces individually differed much between 5.3% to 27.5% of the static forces in the same positions. On the Powerplate, they were even close to zero in some subjects. The total forces were always below 79% of the forces during walking. The dynamic forces did not rise proportionally to platform accelerations. During stance (Galileo, 25 Hz, 2 mm), the damping of dynamic forces was only 8% between foot and knee but 54% between knee and hip. The estimated rises in muscle forces due to the vibrations were in the same ranges as the contact force increases. These rises were much smaller than the vibration-induced EMG increases, reported for the same platform accelerations. These small muscle force increases, along with the observation that the peak contact and muscle forces during vibrations remained far below those during walking, indicate that dynamic muscle force amplitudes cannot be the reason for positive effects of whole body vibrations on muscles, bone remodelling or arthritic joints. Positive effects of vibrations must be caused by factors other than raised forces amplitudes.

Physical Activities That Cause High Friction Moments at the Cup in Hip Implants.

BACKGROUND: High friction moments in hip implants contribute to the aseptic loosening of cementless cups, of which there are approximately 100,000 cases per year; sustained joint loading may cause such high moments. The most "critical" physical activities associated with sustained joint loading were identified in this study. METHODS: Friction moments in the cup were telemetrically measured about 33,000 times in the endoprostheses of 9 subjects during >1,400 different activities. The highest moments were compared with the cup's fixation stability limit of approximately 4 Nm. RESULTS: A total of 124 different activities caused friction moments meeting or exceeding the critical limit, with the highest value of 11.5 Nm. Most involved sustained high contact forces before or during the activity. The highest peak moments (6.3 to 11.5 Nm) occurred when moving the contralateral leg during 1-legged stance, during breaststroke swimming, muscle stretching, 2-legged stance with muscle contraction, and during static 1-legged stance. The median moments were highest (3.4 to 3.9 Nm) for unstable 1-legged stance, whole-body vibration training, 2-legged stance with an unexpected push at the upper body, 1-legged stance while exercising the contralateral leg, and running after 2-legged stance. CONCLUSIONS: Frequent unloading plus simultaneous movement of the joint are required to maintain good joint lubrication and keep the friction moments low. Frequent, sustained high loads before or during an activity may cause or contribute to aseptic cup loosening. During the first months after hip arthroplasty, such activities should be avoided or reduced as much as possible. This especially applies during postoperative physiotherapy. Whether these guidelines also apply for subjects with knee implants or arthrotic hip or knee joints requires additional investigation. CLINICAL RELEVANCE: The risk of aseptic cup loosening may be reduced by avoiding sustained loading of hip implants without periodic joint movement.

In vivo measured joint friction in hip implants during walking after a short rest.

INTRODUCTION: It has been suspected that friction in hip implants is higher when walking is initiated after a resting period than during continuous movement. It cannot be excluded that such increased initial moments endanger the cup fixation in the acetabulum, overstress the taper connections in the implant or increase wear. To assess these risks, the contact forces, friction moments and friction coefficients in the joint were measured in vivo in ten subjects. Instrumented hip joint implants with telemetric data transmission were used to access the contact loads between the cup and head during the first steps of walking after a short rest. RESULTS: The analysis demonstrated that the contact force is not increased during the first step. The friction moment in the joint, however, is much higher during the first step than during continuous walking. The moment increases throughout the gait cycle were 32% to 143% on average and up to 621% individually. The high initial moments will probably not increase wear by much in the joint. However, comparisons with literature data on the fixation resistance of the cup against moments made clear that the stability can be endangered. This risk is highest during the first postoperative months for cementless cups with insufficient under-reaming. The high moments after a break can also put taper connections between the head and neck and neck and shaft at a higher risk. DISCUSSION: During continuous walking, the friction moments individually were extremely varied by factors of 4 to 10. Much of this difference is presumably caused by the varying lubrication properties of the synovia. These large moment variations can possibly lead to friction-induced temperature increases during walking, which are higher than the 43.1°C which have previously been observed in a group of only five subjects.

Standardized Loads Acting in Hip Implants.

With the increasing success of hip joint replacements, the average age of patients has decreased, patients have become more active and their expectations of the implant durability have risen. Thus, pre-clinical endurance tests on hip implants require defining realistic in vivo loads from younger and more active patients. These loads require simplifications to be applicable for simulator tests and numerical analyses. Here, the contact forces in the joint were measured with instrumented hip implants in ten subjects during nine of the most physically demanding and frequent activities of daily living. Typical levels and directions of average and high joint loads were extracted from the intra- and inter-individually widely varying individual data. These data can also be used to analyse bone remodelling at the implant-bone interface, evaluate tissue straining in finite element studies or validate analytical loading predictions, among other uses. The current ISO standards for endurance tests of implant stems and necks are based on historic analytical data from the 1970s. Comparisons of these test forces with in vivo loads unveiled that their unidirectional orientations deviate from the time-dependent in vivo directions during walking and most other activities. The ISO force for testing the stem is substantially too low while the ISO force for the neck better matches typical in vivo magnitudes. Because the magnitudes and orientations of peak forces substantially vary among the activities, load scenarios that reflect a collection of time-dependent high forces should be applied rather than using unidirectional forces. Based on data from ten patients, proposals for the most demanding activities, the time courses of the contact forces and the required cycle numbers for testing are given here. Friction moments in the joint were measured in addition to the contact forces. The moment data were also standardized and can be applied to wear tests of the implant. It was shown that friction only very slightly influences the stresses in the implant neck and shaft.

Medial and lateral foot loading and its effect on knee joint loading.

BACKGROUND: The medial knee contact force may be lowered by modified foot loading to prevent the progression of unilateral gonarthrosis but the real effects of such gait modifications are unknown. This study investigates how walking with a more medial or lateral rollover of the foot influences the in vivo measured knee contact forces. METHODS: Five subjects with telemeterized knee implants walked on a treadmill with pronounced lateral or medial foot loading. Acoustic feedback of peak foot pressure was used to facilitate the weight bearing shift. The resultant contact force, Fres, the medial contact force, Fmed, and the force distribution Fmed/Fres across the tibial plateau were computed from the measured joint contact loads. FINDINGS: During lateral foot loading, the two maxima of Fres during the stance phase, Peak 1 and Peak 2, increased by an average of 20% and 12%, respectively. The force distribution was changed by only -3%/+2%. As a result, Fmed increased by +16%/+17%. Medial foot loading, on the other hand, changed Fres only slightly, but decreased the distribution by -18%/-11%. This led to average reductions of Fmed by -18%/-18%. The reductions were realized by kinematic adaptations, such as increases of ankle eversion, step width and foot progression angle. INTERPRETATION: Medial foot loading consistently reduced the medial knee compartment, and may be a helpful gait modification for patients with pronounced medial gonarthrosis. The increase of Fmed during lateral foot loading was most likely caused by muscular co-contractions. Long-term training may lead to more efficient gait and reduce co-contractions.

Postoperative changes in in vivo measured friction in total hip joint prosthesis during walking.

Loosening of the artificial cup and inlay is the most common reasons for total hip replacement failures. Polyethylene wear and aseptic loosening are frequent reasons. Furthermore, over the past few decades, the population of patients receiving total hip replacements has become younger and more active. Hence, a higher level of activity may include an increased risk of implant loosening as a result of friction-induced wear. In this study, an instrumented hip implant was used to measure the contact forces and friction moments in vivo during walking. Subsequently, the three-dimensional coefficient of friction in vivo was calculated over the whole gait cycle. Measurements were collected from ten subjects at several time points between three and twelve months postoperative. No significant change in the average resultant contact force was observed between three and twelve months postoperative. In contrast, a significant decrease of up to 47% was observed in the friction moment. The coefficient of friction also decreased over postoperative time on average. These changes may be caused by 'running-in' effects of the gliding components or by the improved lubricating properties of the synovia. Because the walking velocity and contact forces were found to be nearly constant during the observed period, the decrease in friction moment suggests an increase in fluid viscosity. The peak values of the contact force individually varied by 32%-44%. The friction moment individually differed much more, by 110%-129% at three and up to 451% at twelve months postoperative. The maximum coefficient of friction showed the highest individual variability, about 100% at three and up to 914% at twelve months after surgery. These individual variations in the friction parameters were most likely due to different 'running-in' effects that were influenced by the individual activity levels and synovia properties.

Activities of everyday life with high spinal loads.

Activities with high spinal loads should be avoided by patients with back problems. Awareness about these activities and knowledge of the associated loads are important for the proper design and pre-clinical testing of spinal implants. The loads on an instrumented vertebral body replacement have been telemetrically measured for approximately 1000 combinations of activities and parameters in 5 patients over a period up to 65 months postoperatively. A database containing, among others, extreme values for load components in more than 13,500 datasets was searched for 10 activities that cause the highest resultant force, bending moment, torsional moment, or shear force in an anatomical direction. The following activities caused high resultant forces: lifting a weight from the ground, forward elevation of straight arms with a weight in hands, moving a weight laterally in front of the body with hanging arms, changing the body position, staircase walking, tying shoes, and upper body flexion. All activities have in common that the center of mass of the upper body was moved anteriorly. Forces up to 1650 N were measured for these activities of daily life. However, there was a large intra- and inter-individual variation in the implant loads for the various activities depending on how exercises were performed. Measured shear forces were usually higher in the posterior direction than in the anterior direction. Activities with high resultant forces usually caused high values of other load components.

Standardized loads acting in knee implants.

The loads acting in knee joints must be known for improving joint replacement, surgical procedures, physiotherapy, biomechanical computer simulations, and to advise patients with osteoarthritis or fractures about what activities to avoid. Such data would also allow verification of test standards for knee implants. This work analyzes data from 8 subjects with instrumented knee implants, which allowed measuring the contact forces and moments acting in the joint. The implants were powered inductively and the loads transmitted at radio frequency. The time courses of forces and moments during walking, stair climbing, and 6 more activities were averaged for subjects with I) average body weight and average load levels and II) high body weight and high load levels. During all investigated activities except jogging, the high force levels reached 3,372-4,218N. During slow jogging, they were up to 5,165N. The peak torque around the implant stem during walking was 10.5 Nm, which was higher than during all other activities including jogging. The transverse forces and the moments varied greatly between the subjects, especially during non-cyclic activities. The high load levels measured were mostly above those defined in the wear test ISO 14243. The loads defined in the ISO test standard should be adapted to the levels reported here. The new data will allow realistic investigations and improvements of joint replacement, surgical procedures for tendon repair, treatment of fractures, and others. Computer models of the load conditions in the lower extremities will become more realistic if the new data is used as a gold standard. However, due to the extreme individual variations of some load components, even the reported average load profiles can most likely not explain every failure of an implant or a surgical procedure.

In vivo hip joint loading during post-operative physiotherapeutic exercises.

INTRODUCTION: After hip surgery, it is the orthopedist's decision to allow full weight bearing to prevent complications or to prescribe partial weight bearing for bone ingrowth or fracture consolidation. While most loading conditions in the hip joint during activities of daily living are known, it remains unclear how demanding physiotherapeutic exercises are. Recommendations for clinical rehabilitation have been established, but these guidelines vary and have not been scientifically confirmed. The aim of this study was to provide a basis for practical recommendations by determining the hip joint contact forces and moments that act during physiotherapeutic activities. METHODS: Joint contact loads were telemetrically measured in 6 patients using instrumented hip endoprostheses. The resultant hip contact force, the torque around the implant stem, and the bending moment in the neck were determined for 13 common physiotherapeutic exercises, classified as weight bearing, isometric, long lever arm, or dynamic exercises, and compared to the loads during walking. RESULTS: With peak values up to 441%BW, weight bearing exercises caused the highest forces among all exercises; in some patients they exceeded those during walking. During voluntary isometric contractions, the peak loads ranged widely and potentially reached high levels, depending on the intensity of the contraction. Long lever arms and dynamic exercises caused loads that were distributed around 50% of those during walking. CONCLUSION: Weight bearing exercises should be avoided or handled cautiously within the early post-operative period. The hip joint loads during isometric exercises depend strongly on the contraction intensity. Nonetheless, most physiotherapeutic exercises seem to be non-hazardous when considering the load magnitudes, even though the loads were much higher than expected. When deciding between partial and full weight bearing, physicians should consider the loads relative to those caused by activities of daily living.

Friction in total hip joint prosthesis measured in vivo during walking.

Friction-induced moments and subsequent cup loosening can be the reason for total hip joint replacement failure. The aim of this study was to measure the in vivo contact forces and friction moments during walking. Instrumented hip implants with Al2O3 ceramic head and an XPE inlay were used. In vivo measurements were taken 3 months post operatively in 8 subjects. The coefficient of friction was calculated in 3D throughout the whole gait cycle, and average values of the friction-induced power dissipation in the joint were determined. On average, peak contact forces of 248% of the bodyweight and peak friction moments of 0.26% bodyweight times meter were determined. However, contact forces and friction moments varied greatly between individuals. The friction moment increased during the extension phase of the joint. The average coefficient of friction also increased during this period, from 0.04 (0.03 to 0.06) at contralateral toe off to 0.06 (0.04 to 0.08) at contralateral heel strike. During the flexion phase, the coefficient of friction increased further to 0.14 (0.09 to 0.23) at toe off. The average friction-induced power throughout the whole gait cycle was 2.3 W (1.4 W to 3.8 W). Although more parameters than only the synovia determine the friction, the wide ranges of friction coefficients and power dissipation indicate that the lubricating properties of synovia are individually very different. However, such differences may also exist in natural joints and may influence the progression of arthrosis. Furthermore, subjects with very high power dissipation may be at risk of thermally induced implant loosening. The large increase of the friction coefficient during each step could be caused by the synovia being squeezed out under load.

In vivo hip joint loads during three methods of walking with forearm crutches.

BACKGROUND: Patients with osteoarthritis, joint implants or fractures use crutches in order to reduce lower limb loading. However, insufficient information exists on how much the loading is then in fact reduced. This situation was studied by using seven patients who had instrumented hip implants. METHODS: Part I: To investigate the effectiveness of forearm crutches, crutch and hip joint contact forces were measured in seven patients with instrumented hip prostheses. Additionally, the bending moments in the implant neck and torsion around its stem were determined. Reductions of peak loads during 3, 4, and 2-point gaits were compared with loads present when walking without crutches. Part II: This examines joint load reduction during a 4-point gait from one to 12 weeks post-operatively. FINDINGS: Part I: During a 3, 4, and 2-point gait, the joint force was 17, 12, and 13% lower than it was while walking without crutches. The corresponding reductions of the bending moment were 16, 11, and 12%, while the maximum torque decreased by 19, 21, and 10%. Part II: The reductions of contact forces in comparison with walking without crutches were highest during the first 4 weeks after surgery. One and 4 weeks post-operatively, the force maximum was 21 and 8% lower than it was after 3 months. When compared with the initial values of the 1st week, crutch forces decreased by 28% in the 4th week and by 38% in the 3rd month. INTERPRETATION: Average reductions of the joint load by more than 20% are achieved only during the first 4 post-operative weeks. Because fractures are in most cases relatively stable after 6 weeks, and bone ingrowth into implant interfaces is nearly finished after this time, a single crutch and a 2-point gait can be prescribed during the 5th and 6th post-operative week.